D-Link KVM-440 Manual do Utilizador

D-Link® KVM-440/KVM-4508/16 Port Combo KVM SwitchUser ManualVersion 1.00

You can connect the KVM switch to computers using one of the three methods shown below: A. Connect USB, PS/2 (keyboard/mouse) and VGA connectors t

C. Connect only USB and VGA connectors to computers. (Figure 9). Figure 9: USB and VGA video connected 4.4. Cascade Chaining The KVM swi

D. Plug in the power adapter for each level Slave KVM Switch and connect Slave KVM switch to computers. E. The power on sequence should be: 1.

Figure 10: Cascade chaining 13

15 6. Hotkey Operation 6.1. Call OSD Menu Press <Scroll Lock> twice and <Enter>, then the OSD “Main Menu” will be displayed on th

Figure 12: Specific channel selection hotkey <Scroll Lock> → <Scroll Lock> → <1> → <Enter> or <Scroll Lock> → <S

17 automatically shift to left or right one channel (channel decrease / increase to next) when the <ALT> channel shift function is enabled.

<Page Up> or <Page Down>, and then press <Enter> to switch to the target port. Please refer section 7.2.2 Channel select to cascad

Figure 14: Auto-scan hotkey Channel Name Channel Number Indicates Scan Mode Figure 15: Auto-scan Banner 6.6.2. Stop Auto-scan Function Pre

Index 1. INTRODUCTION ...

<Enter>. The KVM will be locked until an authorized user logs in. <Scroll Lock> → <Scroll Lock> → <H> → <Enter> To u

¾ A plus mark (+) showing in the left of channel name indicates that the port that is cascaded. 7.1.3. Computer & KVM Status ¾ KVM buzzer st

on the second page. Since the port information is divided onto two pages, the page down / up indicator is a reminder to switch to alternative pages

Channel Name Channel Number 2nd Layer Channel Number 1st Layer Channel Number Fig. 18: Channel Banner (Cascade Layer) 7.2.3. Return from Cas

7.3.2. Scan Time The default scan time is 5 seconds. Scan time can be increased to up to 90 seconds at 5 second increments. 7.3.3. Banner Time T

Note: You can also change the leading hotkey via hotkey using <CTRL> → <CTRL> → <New Hotkey> → <Enter> outside the OSD mode.

7.4.3. Auto-scan Mode There are two auto-scan modes, please refer section 7.3.1 Setup in OSD – Scan Mode to set up the auto-scan mode. ¾ Scan all

7.6. Channel Rename: <F4> Select the channel to rename using the up/down arrow key and press <F4> from the OSD main menu. The channel

Figure 27: Security setup main window 7.7.2. Security Mode To change the security mode setting, please move the highlight bar to Security Mode, a

7.7.4. Authorized User Setup Up to 3 authorized users can manage the KVM switch. To change the user name and password, please move the highlight ba

3 7.1.6. Page Up / Down Indicator ... 21 7.1.7. Function Co

7.8. Lock Port: <F6> 7.8.1. Lock Port Only the administrator can lock the port. Please move the highlight bar to the channel to lock, and

31 8. Sun Microsystems Function Key Emulation: There are 16 special functions on the Sun Microsystems keyboard, Combo KVM Switch can emulate thes

9. Troubleshooting : Symptom Possible Cause Recommended Solution Keyboard and/or Mouse not working Keyboard and/or Mouse need to be reset. Unplu

33 10.Firmware Upgrade Procedures The KVM switch provides the firmware upgrade for the following functions:  USB console: Update for USB consol

34 6. Use the mini-USB cable to connect KVM firmware update port and the USB port of computer which runs the firmware update utility. Figu

35 Figure 36 9. Select the firmware file to update. Figure 37 10. Click the “Program” button to start firmware programming. Figure 38

36 11. A status bar is shown under the panel to indicate the update progress. Figure 40 Figure 39 12. The firmware is updated

37 Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (im

1. Introduction Thank you for purchasing a D-Link Combo KVM Switch. You now have a durable, high quality system to control multiple PCs via a sing

5 Package Contents The product you purchased should contain the following equipment and accessories: 1 x 8-Port or 16-Port Combo KVM Switch 1 x

Selected (Red):The red LED indicates that the corresponding PC is selected.On-Line (Green):The green LED indicates that the corresponding PC is online

7

4.3.2. Console Connection: Plug the keyboard, mouse, and monitor into the console ports on the rear panel of the KVM Switch. (Figure 5) Figure 5:

4.3.3. System Connections: Use the custom combo cable to connect your computers. Refer to the figures and instruction shown below for information