D-Link DI-714 Manual do Utilizador

D-Link DI-714 Wireless Broadband Router User’s Manual Rev. 020205F

10IP Security (IPSec) IPSec provides a more secure network-to-network connection across the Internet or a Wide Area Network (WAN). IPSec encrypts al

11 Installation Considerations Designed to go up to 300 feet indoors and up to 900 feet outdoors, D-Link Air lets you access your network from virtua

12For the average American multiple bedroom home, range should not be a problem. If you experience low or no signal strength in areas of your home t

13Front Panel The front panel provides LED lights to indicate the status of the unit. Refer to the following table for the meaning of each LED featu

14Local Ethernet 1 2 3 4 The Ethernet ports used to connect devices capable of Ethernet connection such as a computer, hub, or switch. The Ethern

15 In order to configure the DI-714 you must input the user-name into the User Name box. Enter the password into the Password box and press the OK b

16Main Page The Main Page screen provides links to the main sections of the web configuration interface. Setup Wizard The Setup Wizard is a step

17Time Settings Please choose the local time zone. After selecting the correct time zone, click on the Next button to continue. You can also c

18Device IP Settings You have to give your Internet gateway an IP address on your “private” network. This is not the “public” IP address from yo

19Cable/DSL ISP Settings The DSL/Cable ISP settings have a default to obtain dynamically the IP address for the WAN port of the broadband router.

2 Contents Introduction ...5 Package Contents ...

20ISP Additional Settings If you would like to use ISP additional settings you have to enable this function and configure this page. Some ISPs use

21Some ISPs, especially cable modem providers, use the “Host Name” to authenticate the user. If this is the case, you will need to enter: Host Nam

22Modem Settings An analog external modem can be used as a dialup backup to the DSL/Cable connection. If you would like to use a modem backup, yo

23Device Information The Device Information screen displays the basic information of your DI-714. The Device Name is the same as the Computer Name t

24Device Status The Device Status screen displays a graphical representation of your current configuration. The left side of the screen shows your c

25The DHCP Log displays information about each IP Address assigned to a computer using the DHCP server built-in to the DI-714. Basic Setup The Basic

26Select Dynamic IP if your ISP has not given you a unique IP address and you receive an automatic IP address each time you connect to your ISP. The

27Advanced Settings DHCP Server Settings By default, the Broadband Router has DHCP server enabled to assign an IP address ranging from 192.168.0.100

28Virtual Server Settings Specific application support is enabled in Virtual Server Settings under Advanced Settings. Click on the arrow to select

29DMZ The Virtual Server Settings under Advanced Settings also enables one computer to have full access to the Internet without the protection of th

3 Device Status...24 Basic Setup...

30Static Routing In Static Routing, the user has the ability to add a static route to the routing table by simple entering the destination IP, subne

31Dynamic Settings By default, the Broadband Router will not send or receive any routing Internet protocols (RIP) to update the routing table. Howe

32Modem String Settings Most dial-up modems are compatible with the standard modem strings. However for modems that require special modem strings,

33Password Settings You can give your Internet gateway a new password. This password will be required the next time and subsequent times you conf

34System Tools The System Tools section enables you to manage your DI-714 and view information related to unit functions. The following functions

35attempts on your network. If any packets are seen as harmful, those packets are blocked and a log is kept about the information related to that pa

36addresses there are and where the router should forward packets when it receives them. Type: The type of routing protocol used. Destination LAN IP

37System Diagnostics The System Diagnostics screen displays current status and connection information. This screen is similar to the Device Status

38 The Configuration section shows important information about your ISP Settings, Modem Settings, and Device Settings as well as the current firmwar

39Upgrade Firmware The Upgrade Firmware screen enables you to update the firmware used in the DI-714. Visit D-Link’s product support site (www.dl

4 Registration...58

40Reset Device The Reset Device screen enables you to reboot the DI-714. If any changes are made and you want them to take effect, you will need

41Troubleshooting In the event that you are unable to connect to or use your DI-714 Wireless Broadband Router, please refer to the following troubl

42LED’s don’t follow the correct boot-up sequence as stated in the Quick Install Guide. Cause:  The unit’s firmware is corrupt.  The unit is not r

43 The NAT table is full. Resolution:  Reboot the Broadband Router by turning the power to the unit off and then on again. Some types of hacker too

44 Use the WINIPCFG utility described in the appendix to make sure that your computer has a compatible IP Address. If your IP Address is not set cor

45ISP Connection Problems I can access the Broadband Router, but I can’t connect to my ISP. Cause:  Your DSL or Cable modem is not functioning cor

46Internet Application Problems My online game does not work. Cause:  The NAT table has filled up.  The correct settings have not been used to ope

47My E-Mail program doesn’t receive my E-Mail Cause:  The Domain Suffix is not set correctly. Resolution:  Some email applications require you to e

48“Introduction to Wireless Networking” for tips to help make a good connection.  Check your IP Address to make sure that it is compatible with the

49Using the PING Utility in Windows 95/98/Me In Windows, Microsoft has provided a small utility called PING that can be used to troubleshoot your IP

5 Introduction Congratulations on your purchase of the D-Link Wireless Broadband Router. Your Wireless Broadband Router enables you to share your DS

50PING, your connection is not complete. If a PING is unsuccessful between you and your DSL or Cable modem, then your connection is not setup corre

51Using the WINIPCFG Utility in Windows 95/98/Me In Microsoft Windows versions 95 through Me, Microsoft has provided a small utility called WINIPCFG

52Renew buttons to receive the correct settings. If you manually set your network settings, make sure that the IP Address of your Broadband Router is

53Technical Specifications Standards: • IEEE 802.3 10BASE-T Ethernet • IEEE 802.3u 100BASE-TX Fast Ethernet • ANSI/IEEE 802.3 NWay auto-negotiation

You can find software updates and user documentation on the D-Link website.D-Link provides free technical support for customers within the United Sta

Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or en

Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy perio

Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGA

Product registration is entirely voluntary and failure to complete or return thisform will not diminish your warranty rights.

6 Broadband Router to expose it to the Internet and ensure complete Internet application compatibility even if specific ports are not known. Unlike

7 Introduction to Broadband Router Technology A router is a device that forwards data packets from a source to a destination. Routers work on the OS

8 built specifically to act as a firewall. In most circumstances, a firewall is used to prevent unauthorized Internet users from accessing private

9 a wireless network card. Most networks use hardware devices such as hubs or switches that each cable can be connected to in order to continue the